SwineFarming.org

Home › Articles › Swine Nutrition Deep Dives › Feed Waste Reduction: Feeder Adjustment and Design

Swine Nutrition Deep Dives

Feed Waste Reduction: Feeder Adjustment and Design

Feed is the largest cost in pork production, and wasted feed is money lost twice: once in purchase and again in manure and rodent pressure. Studies of finishing barns have found that poorly adjusted feeders can waste a meaningful share of feed, and fixing them is among the cheapest improvements on a farm. This article explains how feeder design and adjustment affect waste, how to measure it, how to manage wet-dry feeders, bins, augers and rodents, and how to build a routine so adjustments are made consistently. Gains show up directly in feed per pound of gain.

Where waste happens

Waste arises at several points: spillage during transport and bin filling, feed left in bins and lines, rodent and bird consumption, and most importantly feed thrown or pushed out of the feeder and lost through slats. Feeder waste is influenced by feeder type, opening size, trough design, pig size and behavior, feed form and pen environment. Because pigs compete and root, some waste is unavoidable, but well-managed feeders can cut it substantially. See feed cost as a percentage of total costs for why this matters.

Reading the feeder pan

The most practical tool is observation. In a properly adjusted dry feeder, the pan should be about half to two-thirds covered with feed, with no feed built up against the back wall and no empty pan. Feed should not be visible beyond the lip, on the floor or in the slats. Observe pigs at feeding time: if they push feed out with their snouts, the gap is too wide. If the pan is bare and pigs chew the opening, it is too narrow. Check each feeder at least weekly, and each time pigs are moved or weights change.

Adjusting the gap

Feeder opening should change as pigs grow. Adjust upward as feed intake rises, and downward when a new group enters. Use the manufacturer's guidance for each model, since mechanisms differ. Typical principles are as follows.

  1. Start with a narrow opening for small pigs and widen gradually.
  2. Check the pan after one hour and again after several hours.
  3. Look for fines accumulation, which indicates the gap is too small or the feed is bridging.
  4. Record the setting and date for each pen.
  5. Use a feeder adjustment gauge where available.

Design features that cut waste

Feeders with agitators, shields, tall dividers and trough lips reduce rooting and throwing. Wet-dry feeders, with a drinker integrated into the feeder, generally reduce waste and feed conversion, as discussed in wet-dry feeders versus dry feeders. Position feeders away from walls where they can be rooted, and make sure floor slats near the feeder are in good repair. Correct feeder space per pig reduces competition and spillage; see feeder space allowance and competitive behavior at feeders.

Feed form and quality

Fines, dust and sticky feed increase waste. Poor pellets and finely ground meal create fines that flow poorly, bridge and are pushed out. See pellet quality and feed particle size. Moisture, mold and sticky ingredients block feeders and lead to off-feed behavior. Keep bins clean and sealed, and avoid letting feed sit in lines for long periods.

Rodents, birds and storage losses

Rodents eat and contaminate large amounts of feed and also carry disease. Keep spilled feed cleaned up, store bagged feed in sealed containers, use tight bins with intact lids and seals, and run a rodent control program. Birds feeding in finishing units add to waste and disease risk; see bird exclusion in finishing units. Leaks in bins allow moisture to cause caking and mold. Inspect bins and delivery points routinely.

Measuring waste

Weigh feed delivered and feed consumed over a full group, then compare feed per pound of gain with benchmarks and with other groups in the same barn. To estimate feeder waste directly, place a tray or sheet beneath the slats near a few feeders and weigh feed collected over a period, or compare pens with different feeder settings. A drop in waste often appears as an improvement of several points in feed conversion. See feed conversion ratio.

Building a routine

Waste control is a habit rather than a project. Assign someone to check feeders at each barn walk, and give them a simple chart showing the target pan coverage. Train new staff to adjust feeders, and review the settings when a new group arrives. Fix broken parts, replace worn feeders and keep spare parts on hand. Report unusual disappearance numbers to the manager. Consider technology, such as sensors, as covered in precision feeding technology, but remember that a simple eye-and-hand routine already delivers most of the gain.

FAQ

How much feed can a poorly adjusted feeder waste?

Waste varies by barn, but a badly adjusted feeder can lose a noticeable percentage of feed, so adjustment is among the cheapest ways to improve conversion.

How full should a feeder pan be?

A good rule is roughly half to two-thirds covered, with no feed pushed out or piled against the back.

Do wet-dry feeders reduce waste?

In many studies they reduce waste and improve feed conversion because pigs drink at the feeder and do not need to root for water.

Keep learning

Browse all 700 guides →