A finishing pig does not need the same diet at 120 pounds that it needs at 280 pounds. Its requirement for lysine, expressed as a percentage of the diet, falls steadily as the pig grows, because maintenance and fat deposition take a larger share of nutrients while protein accretion slows. Phase feeding matches the diet to the pig more closely, trimming wasted protein and feed cost without sacrificing growth or lean. This article explains how requirements change, how many phases make sense, how to set transition points, and how to check whether the program is actually working on your farm.
Why one diet fits nobody well
A single finisher diet is always a compromise. If it is formulated to meet the needs of the lightest pigs in the barn, it over-supplies amino acids to the heavier ones, and the extra nitrogen is simply excreted. If it is formulated for the average pig, the lightest animals are under-fed and the heaviest are over-fed. Lysine is the reference amino acid because it is usually first-limiting in corn and soybean meal diets, and every other essential amino acid is set relative to it. Because lysine is also the most expensive nutrient to supply on a per-unit basis, errors here cost real money. See Lysine and Amino Acids in Swine Diets for the basics.
How requirements fall with body weight
Standardized ileal digestible (SID) lysine requirements are usually expressed two ways: as a percentage of the diet and as grams per day. The percentage drops across the finishing period, while the daily gram intake needed rises early and then plateaus or declines slightly as protein deposition slows relative to maintenance. Typical ranges for modern lean genotypes run roughly as follows, and your genetics supplier or nutritionist should confirm the exact figures for your pigs.
| Body weight range | Approximate SID lysine, % of diet |
|---|---|
| 50 to 100 lb | 0.95 to 1.05 |
| 100 to 150 lb | 0.80 to 0.90 |
| 150 to 200 lb | 0.68 to 0.78 |
| 200 to 280 lb | 0.58 to 0.68 |
Barrows need less than gilts at the same weight, and intact males and immunocastrates need more. Energy density and feed intake also matter, so the lysine-to-calorie ratio is a better guide than the percentage alone.
How many phases are worth it
Research and field experience generally show diminishing returns. Moving from one diet to two phases captures a large share of the possible savings. Going to three or four phases captures some more, and daily-blend or multi-phase systems approach the theoretical optimum. The practical limit is the number of bins, the mixing capacity of your mill, and the labor to switch diets accurately.
- Two phases: the minimum for any commercial barn, usually split near 150 to 170 pounds.
- Three to four phases: the common target for farms with enough bin space or a commercial supplier.
- Blending systems: two base diets blended in changing ratios by an automated feeder, which reduces transition lines almost to nothing.
Setting transition points
Switch by body weight or by feed disappearance, whichever you can measure reliably. Weight-based triggers need periodic sampling of the pen, because average weights drift away from the planned curve when health challenges or heat slow growth. Feed-budget triggers, where each pig is allotted a fixed number of pounds per phase, are simple and work well when pig flow and group sizes are consistent. Avoid switching on calendar date alone unless growth is very predictable. A common error is leaving the growing diet in the feeder until the bin is empty, which can carry a high-lysine diet far past the planned transition.
Using crystalline amino acids to fine-tune
Phase diets get cheaper when synthetic lysine, threonine, tryptophan and methionine replace part of the soybean meal as the pig gets heavier. Lower crude protein in late finishing reduces nitrogen excretion and often improves water and heat balance. Keep the ideal protein ratios intact, so valine, isoleucine and other amino acids do not become limiting as crude protein falls. Our guides on low-protein diets and amino acid ratios explain the limits.
Sex, genotype and health effects
Splitting pens by sex lets you feed gilts and barrows differently, and most of the saving comes from lowering lysine for barrows in the late phases. Leaner genotypes carry higher requirements than fatter ones, which is why a diet bought on price from one supplier can underperform on a different genetic line. A pig fighting a respiratory or enteric challenge eats less, so its percentage requirement rises even as its daily protein deposition falls. When intake is depressed, consider adding a modest margin to the percentage rather than keeping the planned figure.
Common mistakes
- Feeding the same lysine level from 50 to 280 pounds because it is simpler.
- Ignoring actual feed intake, so the diet is formulated for appetite the pigs do not show.
- Switching diets without flushing feeders, which blends two phases for days.
- Using book values for ingredient digestibility without checking the delivered diet by laboratory analysis.
- Cutting lysine too deeply in the last phase, which can raise backfat and reduce lean yield.
- Not recording the date and weight of each switch, so results cannot be traced.
Measuring whether it works
Compare phase programs on cost per pound of gain and on carcass value, not feed cost per ton. A cheaper diet that raises feed conversion or adds backfat can lose money, as the feed conversion ratio guide shows. Run side-by-side groups in the same barn when possible, and track average daily gain, feed per gain, lean percentage and any premium or discount at the packer. Revisit the program whenever genetics, feed prices or the packer grid change. Tools described in precision feeding technology can make this far more granular for larger operations.
FAQ
How many diets should I feed between 50 and 280 pounds?
At least two, and three or four if your mill and bins allow it; most of the benefit comes from the first extra phase, with smaller gains after that.
Does lowering lysine in late finishing hurt carcass quality?
A moderate reduction matched to the pig's falling requirement does not, but cutting too deep can reduce lean percentage and increase backfat, so keep within the range your nutritionist recommends.
Should gilts and barrows get different diets?
Where pen sorting by sex is practical, yes, because barrows typically need less lysine than gilts in the heavier weight ranges and the saving adds up over a full barn.