Pigs do not need protein; they need amino acids in the right proportions. The ideal protein concept expresses every essential amino acid as a ratio to lysine, so that a diet can be balanced by setting lysine and then adding the others in proportion. Getting these ratios right controls lean gain, fat deposition and feed efficiency, and therefore carcass composition and value. This article explains the ideal protein ratios, how they change with weight, sex and genotype, how to apply them to real diets and how to verify results with carcass data.
The ideal protein concept
Lysine is the first-limiting amino acid in most cereal and soybean diets and the reference point for the rest. The ideal protein profile gives the amount of threonine, methionine plus cysteine, tryptophan, valine, isoleucine and others relative to lysine at 100. If any amino acid falls below its ratio, it limits protein deposition and the pig deposits more fat or wastes the extra amino acids. Read Lysine and Amino Acids in Swine Diets: A Plain-English Guide for the basics and Crystalline Amino Acid Inclusion Rates: A Meta-Analysis for how crystalline sources are used.
Typical ratios in growing and finishing pigs
Published ratios vary slightly between sources and with the basis used, standardized ileal digestible or total. The following are commonly cited approximate values for growing-finishing pigs relative to lysine, and should be treated as a guide to confirm with your nutritionist.
| Amino acid | Approximate ratio to lysine (SID basis) |
|---|---|
| Threonine | 0.60 to 0.65 |
| Methionine plus cysteine | 0.55 to 0.60 |
| Tryptophan | 0.16 to 0.18 |
| Valine | 0.65 to 0.70 |
| Isoleucine | 0.52 to 0.55 |
| Leucine | 1.00 or more |
Threonine and methionine plus cysteine ratios tend to increase slightly in later growth stages because maintenance needs, which are high in sulfur amino acids and threonine, make up a larger share of the total requirement.
How requirements change with weight
Young pigs deposit mainly protein, so their lysine requirement as a percentage of the diet is high. As pigs get heavier, they deposit more fat, feed intake rises, and the percentage of lysine in the diet falls. This is why phase feeding saves money, see Phase Feeding in Finishing Pigs: Precision Lysine Adjustments. If the diet is not changed as pigs grow, lysine is oversupplied in late finishing, wasting protein cost and raising nitrogen excretion, as discussed in Low-Protein Diets: Environmental and Performance Outcomes.
Genotype, sex and carcass goals
Lean, fast-growing genetics have higher daily protein deposition and therefore higher lysine requirements than fatter genotypes. Entire males generally need more lysine than barrows, and gilts fall between them. Castrates deposit more fat and eat more. Immunocastrated males shift in requirement over time. The carcass target matters too: if the market pays a premium for loin eye area and penalizes backfat, a higher lysine-to-energy ratio is justified. If it pays for marbling, as in some premium markets, a slight lysine restriction in late finishing may raise intramuscular fat but costs lean yield. See Boar Taint: Detection and Control for entire male considerations.
Lysine to energy ratio
Because pigs eat to meet energy needs, a simple and useful metric is grams of SID lysine per megacalorie or megajoule of net energy. Formulating on this ratio protects against over- or under-supply when energy density changes with fat additions or ingredient swaps. For example, if you add fat to boost energy in summer, you must also raise lysine to maintain the ratio, see Seasonal Diet Adjustments: Summer vs. Winter Formulations.
Applying ratios in practice
- Obtain current requirement tables for your genetics from your supplier or a recognized swine nutrient requirements source.
- Use ingredient digestibility values and analyses, since average book values can mislead.
- Fix lysine at the target level for each phase.
- Set minimums for other amino acids as a ratio to lysine.
- Use crystalline lysine, threonine, methionine and tryptophan to fill gaps economically.
- Check that valine and isoleucine are not limiting if protein is low.
- Review each phase with a nutritionist whenever prices or ingredients change.
Verifying with carcass data
Collect packer sheets showing carcass weight, backfat, loin depth and lean percentage by group. Track feed conversion and days to market. If backfat rises with no change in feed intake, the diet might be short of an amino acid, or energy is too high. If lean percentage is high but feed cost is excessive, the lysine level may be above what the pigs need. Run controlled comparisons rather than reacting to single groups. See Feed Conversion Ratio in Pigs: How to Calculate and Improve FCR and Phase Feeding in Finishing Pigs: Precision Lysine Adjustments.
Common mistakes
- Using the same ratios for all genotypes.
- Ignoring digestibility and using total amino acids.
- Overfeeding protein to be safe, which wastes money and increases nitrogen excretion.
- Forgetting that heat and health challenges change intake and therefore amino acid concentration needs.
- Using lysine as the only checkpoint and neglecting threonine and tryptophan.
FAQ
What is ideal protein?
A diet in which all essential amino acids are provided in the proportions the pig needs, expressed as ratios to lysine, so none is in excess or limiting.
Do boars and gilts need different lysine?
Yes. Entire males typically need more lysine than gilts, and barrows need less per unit of energy, so sex-split feeding can pay.
Can I improve carcass quality just by raising lysine?
Only up to the requirement. Beyond that, extra lysine adds cost without more lean, so balance other amino acids and energy.