Particle size is one of the cheapest levers on feed efficiency. Grinding grain finer increases the surface area available to digestive enzymes, which improves energy and nutrient digestibility, but fine grinding costs energy, lowers mill throughput and raises the risk of gastric ulcers. This article compares roller mills and hammer mills, describes target particle sizes for different pigs, explains how to measure particle size, and shows how to balance feed-efficiency gains against grinding costs and health risks.
Why particle size matters
Digestion of starch and protein starts at the surface of a particle. Finer grinding increases the number of surfaces, so more nutrients are digested before the feed leaves the small intestine. Experiments show that feed conversion improves roughly in line with the reduction in particle size, within limits, with typical gains of about 1 to 1.5 percent in feed per gain for every 100 micron reduction. Very fine particles bring down intake and increase dust, ulcer risk and bridging in bins, so there is an optimum.
Targets by pig class
| Pig class | Typical target mean particle size |
|---|---|
| Nursery pigs | 500 to 700 microns |
| Growing and finishing pigs | 600 to 700 microns |
| Gestating and lactating sows | 600 to 800 microns |
Many commercial mills run coarser than these values. For finishing diets, moving from 900 to 700 microns often improves feed conversion with an acceptable ulcer risk. The right target depends on your mill, ingredients, pelleting and veterinary advice.
Hammer mills
Hammer mills shatter grain with rotating hammers against a screen. They are versatile, handle many ingredients including fibrous co-products, and are common on farms. They produce a wider particle size distribution with more fines, use more energy per ton at fine grinds, and are noisy and dusty. Screen size, hammer wear and moisture all influence output. Replace worn hammers and screens regularly, since wear raises average particle size.
Roller mills
Roller mills crush grain between pairs of corrugated rollers. They typically use less electricity, run quieter, produce a more uniform particle size with fewer fines, and generate less heat. Their limitations are greater difficulty with variable grains, a smaller range of achievable fineness for some grains, and the need to maintain roll corrugations. Roll gap adjustment is critical, and moisture changes can affect the result. For many farm mills, a roller mill gives better economics at moderate fineness.
Comparing the economics
Calculate cost per ton: electricity or fuel, labor, maintenance, wear parts and the value of lost capacity. Then compare to the feed saved. A feed conversion improvement of 1 percent on a pig consuming about 600 pounds of feed during finishing saves roughly 6 pounds of feed per pig. Roller mills often win when the target size is above about 600 microns, and hammer mills may be needed for fine grinding or fibrous ingredients. Include the effect on pelleting and the cost of pellet mill energy in your budget.
Ulcers and fine grinding
Finely ground, pelleted feed increases the risk of gastric ulcers in the pars esophagea of the stomach. Signs include pale pigs, black feces, sudden deaths and poor performance. Risks rise with particle size under about 500 microns, pelleting, long fasting and stress. Mitigate by avoiding extreme fine grinds, using coarser grinds for sows and finishers, feeding meal rather than pellets when feasible, and discussing diet fiber and stress management with your veterinarian. See pellet quality for pellet effects.
Measuring particle size
Use a laboratory sieve shaker with a stack of screens, following a standard method, to calculate mean particle size and the spread of the distribution. Sample from the mill outlet and from the feeder, because handling creates fines. Test at least weekly and after screen or roller changes. A coefficient of variation or standard deviation tells you about uniformity; very wide distributions waste energy. Record results alongside feed conversion.
Practical steps
A few farm-level checks make the numbers more reliable. Grain moisture changes grinding behavior, so measure it when you adjust the mill, since wet corn grinds coarser through the same screen. Check that the mixer is not creating fines by over-mixing, and that augers and bins are not segregating coarse and fine particles; a feeder sample that differs greatly from the mill sample points to a handling problem. Keep the sieve set clean and dry, and train more than one person to run it consistently.
- Measure current particle size at the mill and the feeder.
- Set a target range for each feed class.
- Adjust screen size or roll gap, then remeasure.
- Maintain mill parts on a schedule.
- Watch for bridging, dust and ulcers.
- Track feed per gain over several groups, not just one.
Combining particle size with feed waste reduction and feed conversion ratio tracking shows the full payback.
FAQ
What is the best particle size for finishing pigs?
Many nutritionists aim for roughly 600 to 700 microns, balancing digestibility against ulcer risk and mill cost.
Is a roller mill better than a hammer mill?
Roller mills usually use less energy and give more uniform particles at moderate fineness, while hammer mills handle diverse ingredients and fine grinds.
Can fine grinding cause ulcers?
Yes, very fine particles, especially in pelleted feed, increase the risk of gastric ulcers, so avoid extremes.