Evaporative cooling pads lower the temperature of air entering a barn by passing it through a wet cellulose or plastic media, so hot, dry air becomes cooler and more humid. In the right climate they can lift pig comfort and performance in summer at modest energy cost. In the wrong climate or with poor maintenance they add humidity without much cooling and can foster bacteria and scale. This article explains how pads work, how to size and maintain them, what water quality does, and how to judge whether they are performing.
How evaporative pads work
Water flows over pad media at the tunnel inlet, and incoming air evaporates some of it. Evaporation absorbs heat, so the air leaves cooler. The best case is cooling to near the wet-bulb temperature, the lowest temperature evaporation can achieve. Pad efficiency, often 70 to 90 percent for good cellulose pads, describes how close the air comes to that limit.
Because humidity rises as temperature falls, pigs lose less heat by panting in a humid barn, so very humid air limits the benefit. See Heat Stress in Pigs: Signs, Prevention and Cooling Methods for the animal side of the equation.
Where pads work best
Pads shine in hot, dry climates, such as the western Plains and Southwest, where the gap between dry-bulb and wet-bulb temperature is large. In humid regions such as the Southeast, the cooling potential on the hottest, muggiest days is much smaller, so combining pads with air speed and other cooling matters.
Check local climate data for typical afternoon dry-bulb and wet-bulb temperatures before investing. In moderate climates, pads may only be needed during short heat events.
Sizing and layout
Pads must provide enough area so air passes through at a modest speed, since high velocities carry water droplets and reduce cooling. Manufacturers publish recommended face velocity ranges and pad thickness. Pad area is matched to the maximum fan capacity of the tunnel fans, see Ventilation Rate Calculations: Tunnel vs. Sidewall.
Put pads on the inlet end of the barn with a proper plenum, seal around them to avoid bypass, and provide water supply, pump, sump and drain. Leave room for maintenance access.
Water quality and scale
Hard water leaves mineral deposits on pads, which restrict airflow and reduce evaporation. Dirty water carries algae and bacteria. Practical steps:
- Test water hardness and salts before installation.
- Bleed off part of the recirculating water to limit mineral concentration.
- Use a filter or screen to keep debris from clogging distribution lines.
- Choose pad material suited to your water.
See Water Quality for Pigs: Mineral and Microbial Standards for general drinking water quality, though cooling water has its own concerns.
Routine maintenance
Pads need regular care:
- Clean distribution pipes and holes so water covers the pad evenly.
- Remove algae and scale with approved cleaners following manufacturer directions.
- Inspect pads for dry spots, sagging or crushing.
- Drain and flush the sump periodically.
- Winterize by draining the system and covering or sealing the pads so cold air does not leak in.
Replace pads when they stop wetting evenly or cooling falls off, which is commonly every several years depending on water.
Biosecurity and hygiene
Standing water and warm conditions can grow bacteria and algae, and pads also trap dust and insects. Keep the area clean, treat the water if needed, and do not let birds or rodents nest in the plenum. See Biosecurity Audits: The 12 Critical Control Points and Rodent-Proof Construction: Sealing Gaps and Entries for exclusion practices. Pads also act as a barrier against wind-borne dust, but they are not a substitute for filtration if your farm uses filtered air for disease control.
Judging performance
Measure inlet and outlet temperatures and humidity in the afternoon. Compare cooling to the theoretical wet-bulb limit. If the cooling is below expectations, check for airflow bypass, uneven wetting or fan problems. Watch pig behavior: panting, spreading out and wet floors suggest heat stress. Evaporative cooling is most effective together with adequate air speed, and sprinklers or drip cooling can complement it, as described in Heat Stress Alleviation: Drip vs. Misting Systems.
Cost and decision guide
Pads add capital cost, water use and maintenance, but they often cost less to run than mechanical refrigeration. They fit large tunnel-ventilated barns in hot climates best. Weigh the value of improved feed intake and growth in summer against costs, and consult your building designer or local extension specialist for climate-specific advice.
FAQ
Do evaporative pads work in humid climates?
They still cool, but less, because the air is already close to saturation on humid days, so combine pads with high air speed and other cooling methods.
How often should cooling pads be replaced?
It depends on water quality and care, but many last several years. Replace them when scale, algae or damage prevents even wetting or reduces airflow.
How much water do evaporative pads use?
Water use varies with climate, barn size and system design. Ask the manufacturer for estimates and plan for both evaporation and bleed-off.