SwineFarming.org

Home › Articles › Swine Housing Deep Dives › Ventilation Rate Calculations: Tunnel vs. Sidewall

Swine Housing Deep Dives

Ventilation Rate Calculations: Tunnel vs. Sidewall

Ventilation removes moisture, gases, dust and heat so pigs stay healthy and comfortable. Sizing it correctly means calculating three rates: a minimum rate for cold weather, a maximum rate for hot weather, and the transition between them. This article explains how those rates are set, what drives each one, and the practical differences between tunnel and sidewall systems. The numbers below are typical ranges, not substitutes for manufacturer specifications or an engineer's design, so confirm against current extension or design guides for your building and climate.

The three ventilation stages

Ventilation works in stages:

  • Minimum ventilation removes moisture and gases in cold weather while conserving heat.
  • Temperature-control ventilation increases airflow as pigs produce more heat.
  • Maximum or hot-weather ventilation removes as much heat as possible to reduce stress.

Each stage uses different fans, inlets and controls. Most problems arise because the minimum rate is set too low, causing damp, gassy barns, or because maximum capacity is inadequate in summer. See Heat Stress in Pigs: Signs, Prevention and Cooling Methods for what happens when cooling falls short.

Minimum rate: moisture and gas control

Minimum rates are based on pig size and number. Smaller pigs need less air per head but more per pound of body weight. Typical per-pig minimum rates in cold weather run from a few cubic feet per minute, or CFM, for newly weaned pigs up to roughly 10 to 20 CFM for finishers, with sows and farrowing rooms having their own values. Use published tables for your pig class.

The rate must be delivered in a way that mixes incoming air with warm barn air before it hits the pigs. Fans set to run continuously or on timers at the minimum keep gases down, while heaters add warmth.

Maximum rate: heat removal

Hot-weather capacity is much larger. Finishing pigs often need on the order of 70 to 120 CFM per pig or more depending on size, climate and cooling method. Sows and larger animals need more. The goal is to maintain pig temperature within a comfortable range while keeping air speed adequate.

Sizing involves total heat output from pigs, heat entering through the roof and walls, and the temperature rise you accept between inlet and exhaust. Ask a building designer for a heat balance if the barn is large or the climate is hot. Add fan capacity beyond minimum design for aging fans, dirty shutters and unexpected heat waves.

Tunnel ventilation

Tunnel systems pull air the length of the barn with large fans at one end and inlets at the other. They are common in large finishing and wean-to-finish buildings.

Key points:

  1. Seal the barn well, because leaks pull air in from unintended places and disrupt flow.
  2. Air speed along the pen contributes to cooling, often target speeds of several hundred feet per minute in hot weather.
  3. Barn length and width determine the cross-section area and therefore air velocity.
  4. Combine with evaporative cooling to reduce incoming air temperature, covered in Evaporative Cooling Pads: Maintenance and Performance.

Sidewall and cross ventilation

Sidewall systems bring air in through inlets along walls or ceiling and exhaust it through fans or ridge openings. Cross-flow can work in narrower barns and in naturally ventilated curtain-sided buildings, see Curtain Systems: Maintenance and Automation.

Inlet design controls how cold air mixes and falls. Ceiling or baffle inlets that jet air along the ceiling avoid cold drafts on pigs in winter. Controllers adjust inlet opening to maintain the right static pressure, often in a modest range such as roughly 0.05 to 0.15 inches of water column, so check your inlet manufacturer's recommendation.

Tunnel versus sidewall comparison

AspectTunnelSidewall/cross
Hot-weather coolingStrong with air speedModerate
Tightness requiredHighModerate to high
Uniformity in lengthGood, with limitsGood across width
Control complexityHigherModerate
Best fitLarge, long barnsNarrower barns, mixed seasons

Many modern barns combine both, using sidewall in cold weather and tunnel in heat.

A simple calculation approach

For a quick estimate:

  1. Count pigs by class and weight.
  2. Multiply by recommended CFM per pig for minimum and maximum.
  3. Add safety margin and account for fan efficiency at operating static pressure.
  4. Compare with available fan curves from the manufacturer.

For example, a barn of 1,000 finishers using 15 CFM per pig at minimum needs about 15,000 CFM at minimum, but using 100 CFM per pig at maximum, about 100,000 CFM. Real designs use manufacturer data, so treat this as an illustration, not a design.

Maintenance and monitoring

Dirty fans, loose belts and clogged shutters can cut airflow by a third or more. Clean and test regularly, calibrate temperature sensors, and check inlets for stuck positions. Install alarms for high and low temperatures. Poor ventilation links directly to disease risk, see Ventilation Failures and Disease Outbreaks: The Link, and to backup planning in Emergency Ventilation: Backup Power and Alarms.

FAQ

How much ventilation does a finishing pig need in summer?

Often on the order of 70 to 120 CFM per pig depending on size and climate, but use manufacturer and extension guidance for your barn.

What is the difference between minimum and maximum ventilation?

Minimum removes moisture and gases while conserving heat in cold weather, while maximum removes as much heat as possible during hot weather.

Is tunnel ventilation better than sidewall ventilation?

Tunnel is typically stronger for hot-weather cooling in long barns, while sidewall works well in narrower buildings and cold weather. Many barns use a combination.

Keep learning

Browse all 700 guides →