The old rule of thumb for pig AI is simple: breed at standing heat, then again about 12 to 24 hours later while the sow still stands. Research and field experience have refined that rule. Because ovulation happens late in estrus and sperm survive for a limited time in the sow's tract, the interval between onset of estrus and ovulation drives how many doses are needed and when. This article revisits the 12-hour window, explains the biology behind it, and shows how to adapt timing to gilts, weaned sows and different semen types.
The biology behind timing
In sows, ovulation usually occurs in the latter part of estrus, often around two-thirds of the way through. Sperm need a short time in the tract to be ready to fertilize, and they remain viable for a limited period. Eggs, once released, also have a limited fertilization life, measured in hours. The goal is to have viable sperm in the oviduct before or shortly after ovulation. Insemination too early or too late leaves a gap and lowers fertilization rate or litter size.
Why estrus length varies
Estrus length is not constant. It varies with parity, season, weaning-to-estrus interval and genetics. Gilts often show shorter heat than sows. Sows that come into heat soon after weaning tend to have longer estrus and later ovulation relative to heat onset, while sows with a long weaning-to-estrus interval tend to have shorter heats; see weaning-to-estrus interval. Because of this, a rigid calendar fits some sows well and others poorly.
The standard protocol
A common approach in conventional AI:
- Check for estrus daily with a boar present; see heat detection and rebreeding.
- Inseminate the first time when the sow first shows a standing response.
- Repeat insemination about every 24 hours while she continues to stand.
- Use fresh, properly stored semen; see semen storage.
Many herds use two to three doses per heat. A sow that stops standing after the first breeding may not need further doses, while one with a long heat may receive a third.
Tailoring by weaning-to-estrus interval
Programs that adapt timing to the individual sow often perform better than rigid ones. Typical logic:
- Short interval (returns to heat early): longer heat and later ovulation, so wait somewhat before breeding or space doses to cover the later ovulation.
- Long interval: shorter heat and earlier ovulation, so breed promptly and consider a second dose sooner.
- Gilts: short heat, so check frequently and breed soon after first standing.
Your veterinarian or genetics supplier can give a schedule that suits your sows and semen type.
Does semen type matter?
Extender and storage affect how long sperm remain fertile. Extended semen that is several days old may survive less well, which means doses should be placed closer to ovulation. Specialty approaches also change the timing needs: deep intrauterine insemination places a smaller dose deeper in the tract and benefits from more careful timing, while sexed semen has stricter requirements still. Frozen semen has a shorter life after thawing; see cryopreservation.
Technique and sow response
Good timing is wasted if the insemination itself is poor. Stimulate the sow with a boar's presence and pressure on her back, use a clean catheter, seat it properly and allow the dose to flow in slowly, taking several minutes. Sows with a strong standing response retain semen better. Backflow of a small amount is normal and not a reason to repeat the dose. Fix housing and stress issues that reduce the standing reflex.
Checking whether timing is the problem
Look for signs:
- Low farrowing rate with normal semen quality.
- Small litters despite normal return rates.
- Many sows with irregular returns.
- Breeding done at fixed times rather than relative to heat onset.
Review records by parity and weaning-to-estrus interval to see which groups underperform. See farrowing rate benchmarks for targets to compare against.
Practical rules for the crew
- Check heat at the same times each day and record the first standing time.
- Record each insemination with the time, the boar, and the technician.
- Do not hold doses so long that they lose quality.
- Retrain staff periodically on technique.
- Review results by technician and by batch.
For the broader picture see artificial insemination in swine.
Seasonal and herd-level effects
Timing rules do not hold constant through the year. In hot months, sows may show shorter or less intense heats, and the standing response can be weaker, which makes the onset harder to pin down. Summer also depresses boar semen quality, so a dose that performs well in winter can underperform in August; see heat stress in pigs. Many herds respond by checking heat earlier and more often in the cooler parts of the day, adding a dose for sows with a long standing period, and monitoring farrowing rate by month. A herd with a strong seasonal infertility pattern should review both cooling and timing rather than only one of them.
Lactation also leaves a mark: sows that lost heavy condition during lactation can have delayed or weaker heats, so feeding and timing problems often appear together.
FAQ
How long after heat starts should I breed a sow?
Typically at the first standing response, then about every 24 hours while she remains in heat, adjusted for her weaning-to-estrus interval.
Is one insemination enough?
Some programs use one for gilts or specific protocols, but most herds use two or more per heat to cover ovulation timing.
Does timing matter for fixed-time AI?
Yes. Hormonal programs aim to synchronize ovulation so that one or two timed doses work; see fixed-time AI.