The gilt pool is the group of replacement females that are being raised, selected, acclimated and prepared for breeding. How well this pool is managed decides how many gilts reach their first service on schedule, how healthy they are when they enter the sow herd, and how long they stay. Poor gilt management is a hidden cause of low farrowing rates, small first litters and early culling. This article covers selection, growth, acclimation, estrus stimulation and records, with practical targets that you can adapt to your own genetics and health program.
Why the gilt pool deserves attention
Replacement gilts typically make up 40 to 50 percent of annual sow replacements in many commercial herds, and gilts farrowed in the first and second parity are a large share of the herd. A gilt that fails to conceive, or leaves the herd before weaning a second litter, is a net financial loss. The pool also needs enough numbers to fill breeding groups each week, with surplus to cover culling for leg problems, poor teat lines and no estrus. See also Gilt Selection: Choosing and Developing Replacement Breeding Females for choosing individual animals.
Sizing and flow
Calculate how many gilts you need to enter the breeding herd each week or cycle. Work backwards from target mated gilts per group and add an allowance for those that fail to cycle, show lameness or are culled for other reasons. Many farms select two or more gilts for each one needed. Flow should be planned so gilts enter the pool at a set age and weight, and so there are always gilts of the right age available when breeding groups are made. Record arrival dates, weights and ear tags.
Selection criteria
Select for structural soundness, good feet and legs, at least 6 well-spaced functional teats per side (usually 14 or more total), a normal vulva and good growth. Avoid gilts with inverted or blind teats, hernias, crooked legs or poor conformation. Compare animals against the genetic index of your supplier. Avoid selecting only on growth rate or leanness because maternal robustness matters (see Maternal Line Selection: Balancing Litter Size and Robustness). Keep notes on the origin, birth litter size and health status of each gilt.
Age, weight and growth targets
Gilts should not be bred at the first heat. A typical program breeds gilts at their second or third heat, at 135 to 150 kg bodyweight and roughly 210 to 230 days of age, though targets depend on genetics. A growth rate that is steady, not rapid, supports skeleton and fat reserves. Feed diets formulated for developing gilts, see Gilt Development Diets: Puberty and Conception Rates. Excess fat and rapid growth can cause leg problems and lower longevity, while very lean gilts may be late to cycle.
Acclimation and health
New gilts need time to adapt to the farm's pathogens before they enter the sow herd. Acclimation typically includes quarantine for several weeks in isolation, followed by exposure to farm microbes in a controlled manner and vaccination under veterinary guidance, see Gilt Acclimation Programs: PRRS and Beyond. Testing for PRRS and other agents should happen before and after arrival. The aim is for the gilt to have immunity but not shed pathogens when she joins the herd. Follow your veterinarian's plan, because needs vary by herd status.
Stimulating estrus
Gilts that do not show heat are a main cause of delay. Contact with a mature boar for 10 to 20 minutes each day, beginning at 160 to 180 days of age, stimulates puberty. Fence-line or physical contact works best, using a boar that is at least 8 months old with strong libido. Avoid heat stress and overcrowding, which delay puberty, and provide enough pen space and good footing. Record each observed heat date, because breeding should occur at the second or third estrus. See Heat Detection in Sows and Gilts: Signs, Timing and Rebreeding and Estrus Synchronization Protocols for Gilts.
Recording and decision rules
Keep an individual record for every gilt, including identification, weights, heat dates, vaccinations, treatments and breeding dates. Set clear rules, for example, any gilt that has not shown heat by 240 days is evaluated or culled. Review gilt performance in the first parity and compare results with entry weight and age. Digital or paper cards are fine as long as they are used consistently, see Swine Record Keeping: What to Track, Templates and Why It Pays.
Common mistakes
- Buying gilts too late, so they enter the herd without acclimation.
- Breeding at first heat or at too light a weight.
- Overfeeding energy so gilts become fat and lame.
- Crowding in pens, causing injuries and stress.
- Not recording heat dates, causing poor timing.
- Keeping a small pool that forces selection of poor animals.
FAQ
At what age should gilts be bred?
Most are bred at their second or third heat, typically around 210 to 230 days and 135 to 150 kg, depending on genetics.
How long should gilt acclimation last?
Typically several weeks, but the exact plan should be set with your veterinarian based on herd health.
How can I stimulate puberty in gilts?
Daily boar contact beginning around 160 to 180 days of age is the most reliable method.